This is an old revision of the document!
Generation 7 Electronics Board-ARM v2.0 is the first Gen7 based on an ARM, an LPC1114FN28. Like all earlier Gen7s it's still easily DIY-able, because this FN28 comes with through-hole pins spaced at 0.1“ (2.54 mm).
Compared to earlier Gen7s it's considerably faster. It has been demonstrated to deliver as many as 130'000 steps/second to the stepper driver, so 1/32 microstepping is no longer a bottleneck. Even at 1/128 microstepping one can achieve reasonable performance.
PCBs, Components and Connector kits are currently sold on the front page of this wiki.
As Gen7 is designed to be manufactured on a RepRap, you can make PCBs yourself instead of buying. How to do this on a RepRap or a general milling machine is described at PCB Manufacturing. Gerbers, PDFs and such are in Gen7's Github repository.
Yet another way is to purchase from one of the many houses specialized in manufacturing prototype PCBs. Gen7 is single sided, so this won't cost a fortune. If you want to sell excess copies, ask Traumflug for a commercial license.
If you want to assemble the collection yourself, see the Parts Lists section.
To assemble or verify these lists, open the layout with gEDA/PCB and export a “BOM”. This will give you a list of all required components.
This list is ordered to match the order of assembly.
|MCP2200||1||U7||This is the USB-TTL adapter chip.|
|Wire 0.56 mm||60 cm||For 9 bridges.|
|Resistor 10 Ohms||2||R11 R12|
|Resistor 560 Ohms||3||R14 R19 R22|
|Resistor 1 kOhms||7||R2 R4 R6 R8 R10 R16 RT1|
|Resistor 4.7 kOhms||1||RT2|
|Resistor 10 kOhms||3||R1 R3 R30|
|Resistor 1 MOhms||2||R5 R7|
|Diode 1N4004||2||D1 D2|
|Coil 10 uH||1||L1|
|Crystal 12 MHz||1||U6|
|Ceramic Capacitor 0.1 uF||10||C8 C9 C10 C11 C12 C13 C14 C16 C17 C19|
|Ceramic Capacitor 22 pF||2||C3 C4|
|LED 3 mm Green||3||LED2 LED5 LED6|
|LED 3 mm Yellow||1||LED3|
|Electrolytic Capacitor 10 uF||4||C2 C5 CT1 CT2|
|Electrolytic Capacitor 100 uF||3||C1 C6 C7|
|Jumper 1 Pair||1||J20|
|Jumper 2 Pairs||1||Fan|
|Jumper 3 Pairs||4||J1…J12|
|Pololu Headers||8||U2 U3 U4 U5||You want 8x 8 pins.|
|LP2950L-33-T92||1||Q3||3.3 V voltage regulator.|
|Socket 28 Pins||1||U1||300 mil wide version.|
|LPC1114FN28||1||This is the main MCU.|
|MOSFET IRLB 8743||2||Q1 Q2|
This list is ordered to match the order of assembly.
|Molex KK254 2 Pin Header||6||Z_MIN Y_MIN X_MIN
TEMP_EXT TEMP_BED EXT_RESET
|Cable Connector for the above||6|
|Crimp Contact for the above||12|
|Molex KK254 4 Pin Header||4||X_MOT Y_MOT Z_MOT E_MOT|
|Cable Connector for the above||4|
|Crimp Contact for the above||16|
|Molex KK254 6 Pin Header||6||SPI1 SPI2|
|Header Molex 26-48-1045 (2 Pin)||1||HEATER_EXT|
|Cable Connector for the above||1|
|Crimp Contact for the above||2|
|Screw Terminal 2 Pin||1||HEATER_BED|
|Disk Power Header||1||CONN2|
|ATX12V Header 8 Pin||1||CONN3|
To connect your Gen7 with a PC, you need a generic USB device cable.
Last not least, you need stepper drivers. Since Pololu offered their A4983 Stepper Motor Driver Carrier, it's board size and pinout has become kind of a de-facto standard, so many other vendors designed with the same metrics, but other stepper driver chips. All of these compatibles should work fine on a Gen7 board, you can even mix them (different types for each axis).
A few commonly seen drivers:
|Pololu A4988 Stepper Motor Driver Carrier|
|Pololu DRV8825 Stepper Motor Driver Carrier, High Current|
|Watterott SilentStepStick||Trinamic TMC2100 based, Open Source.|
As this is done only once in a Gen7's lifetime and comes with lots of pictures, assembly instructions have been moved over to the Gen7 Board-ARM 2.0 Assembly page.
Soldering completed? Fine. All obvious flaws, if any, fixed? Excellent.
I'ts good manufacturing practice to do some measurements on the board before inserting the central chip, the MCU. Not only because the MCU is the most expensive part on the board, also because this parts connects many other parts together, so a fault in one section harms then other sections, too.
For all these measurements a cheapo voltage meter is entirely sufficient.
At this point the yellow LED on the board should light up. If it doesn't, find the cause and fix it.
To make this step complete, measure the voltages shown in the picture. Deviations of half a volt are OK, but substantially different voltages, especially ones above 6 volts, are not. GND of the meter can be connected to one of the black wires of the ATX24 connector. All other pins of the LPC1114 socket should read (close to) zero volts.
Note: the pin marked 1…3.3 V is on 3.3 volts over a 1 megaohms resistor. Cheap voltage meters have an inner resistance of 1 megaohms, too, so you'll measure there only 1.65 V, while it actually is 3.3 V. Better meters have a higher inner resistance and indicate much closer to the true value.
With these steps done you can be reasonably sure to not burn your LPC1114 when inserting.
Next step is to measure voltages with the power supply turned on.
At this point the PSU should turn on, which can be recognized by its fan turning on as well. The green LED near the yellow LED should light up as well.
Additional voltage measurements with turned on power supply. Standby measurements should be still valid. Unlike in the picture, the LPC1114 socket should be still empty.
As before, measure all voltages shown in the picture. The 12 V and the two 3.3 V measurements repeat on each stepper driver socket. Also measure all the Standby voltages again, including the zero volts pins on the LPC1114 socket.
With everything being within range, especially no 12 volts on the LPC1114 socket, you can be reasonably sure that all your power supply circuitry is fine. Well done!
Having this done you can remove the paperclip from the ATX24 connector. The controller will turn on and off the PSU on it's own before too long.
That's right, the USB adapter can be tested before inserting the LPC1114.
At this point a new serial port should appear in your PC operating system. On Linux that's typically /dev/ACMx, on Windows a COM port in the device manager, on OS X /dev/ttyxxxxx, each time the 'x's replaced with a unique number or identifier.
That's it already, if the device appears, it works.
Finally the central part, the LPC1114 can be inserted into its socket. These chips have a groove at one end. This groove should point to the ATX24 connector.
Sometimes it's neccessary to bend both pin rows a bit closer together to make it fit.
Then press the chip carefully in and … hardware is completed. Yikes!
Gen7-ARM runs Teacup Firmware. Not yet fully integrated into Configtool, yet, so configuring and uploading a firmware takes several steps.
You need a compiler, of course. While it's likely possible to get away with Arduino IDE somehow, please prefer GNU ARM Embedded Toolchain, which is provided by ARM employees.
Having this toolchain available you're ready to go.
For this part we can use the convenient Configtool.
At this point you can adjust everything on the Printer tab. Do not change settings on the Board tab. When done, save the configuration with Menu → File → Save config.h.
In the unlikely case you have to adjust something on the board, e.g. the pinout, you have to do this with a text editor directly in board.gen7-arm.h, after saving config.h like shown above.
Makefile-ARM is a prepared makefile, but needs some adjustments to your local environment. First, make a copy and name it Makefile.
Then open Makefile with a generic text editor and search the words TOOLCHAIN as well as UPLOADER_PORT. Adjust each value to what you have, explanations are in the comments above these words. Other adjustments aren't needed, Teacup currently supports only this one ARM based board (and many AVR based ones).
Now you can compile the firmware from the command line:
It should build flawlessly, taking only a few seconds.
The LPC1114 comes with a bootloader already installed, so unlike with AVRs, no bootloader upload neccessary. If you didn't already, find and install a tool named lpc21isp. The version coming with Debian/Ubuntu's packaging system works just fine.
To activate this bootloader, you have to place the programming jumper. It's the single jumper just top of the reset button. After doing so, press and release the reset button.
Then you can send the firmware:
This should upload the firmware. If there are just waiting dots, check the programming jumper and press reset again. Actually it doesn't matter wether you send the
make or get the LPC into programming mode, first.
After the upload is done, remove the programming jumper. If there are errors, please read and try to solve them.
For details on uploading firmware in general see LPC1114 Bootloader. Technical detail: setting the programming jumper pulls PIO0_1 low; PIO0_1 is also used for the Step signal of the Z axis.
Board-ARM v2.0 is the latest development, so let's collect here experience and possible enhancements for the next version.
For an idea using the serial control lines see http://www.mikrocontroller.net/topic/281717#2977141. Not sure wether this can really work for programming, though and for printing it's sometimes even counterproductive (like when continueing an aborted print).
The first ARM based Generation 7 Electronics was created. It was mostly a Gen7 v1.4.1 with the ATmega replaced by an NXP LPC1114FN28. It worked on the spot.
Bobc's proof of concept video
RepRap user Bobc was the first to run a printer with a Gen7-ARM.
See also his RepRap forum post. To get a working firmware he ported Teacup Firmware to ChibiOS. Later investigations showed that this choice didn't exactly result in the best possible performance, but this didn't matter at that time.
Instead of slowly fading away from DIYers memories due to the lack of new versions/features/whatever, Generation 7 Electronics gets more and more attention. So development was picked up again. A lot of smaller refinements happened and, most importantly, a generic, fast port of Teacup Firmware to ARM was done. Suddenly a Gen7 could outperform a Smoothieboard.