User Tools

Site Tools

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
start [2015/10/27 16:22] – Separate ordering and legal stuff. Traumflugstart [2018/05/29 23:29] (current) – [General Data Protection Regulation (GDPR)] About videos, further refinements. Traumflug
Line 1: Line 1:
 Welcome to RepRap DIY, outlet of Markus "Traumflug" Hitter, developer of RepRap's Generation 7 Electronics. Welcome to RepRap DIY, outlet of Markus "Traumflug" Hitter, developer of RepRap's Generation 7 Electronics.
  
-====== Generation 7 Electronics ======+===== Generation 7 Electronics =====
  
 **Generation 7 Electronics** is a RepRap controller designed to be do-it-yourselfable and replicable. Replication is what makes RepRap unique. **Generation 7 Electronics** is a RepRap controller designed to be do-it-yourselfable and replicable. Replication is what makes RepRap unique.
  
-{{ gen7:gen7_board_1.4.1.jpeg|The picture shows a Gen7 v1.4.after assembly, which approximately looks like a Gen7 v1.5}}+{{ gen7:gen7_board-arm_2.0_front.jpeg?400|A Generation 7 Electronics v2.after assembly.}}
  
-The circuitry design is very similar to other single/stacked board solutions, like RAMPS or Sanguinololu. Generation 7 Electronics can drive the same hardware, can run the same firmwares. Additionally, it comes with a number of detail improvements to make it more flexible, as well as more reliable.+The circuitry design is very similar to other single/stacked board solutions, like RAMPS or Sanguinololu. Generation 7 Electronics can drive the same hardware. Just fasterbecause it features a ARM 32-bit CPU. Additionally, it comes with a number of detail improvements to make it more reliable.
  
-For details, see [[http://reprap.org/wiki/Gen7_Board_1.4.1 | Generation 7 Electronics in the RepRap Wiki]]. The PCBs are manufactured on a RepRap machine and the kit's contents match the tables on the Wiki page, including connectors and solder/crimp pins. The ATmega is equipped with a bootloader already, so there's no need for a programmer.+For details, see the [[Gen7 Board-ARM 2.0]] page. The PCBs are manufactured on a RepRap machine and the kit's contents match the tables on the Wiki page, including connectors and solder/crimp pins.
  
-===== Orderable Items =====+==== Orderable Items ====
  
 |Name |Price with VAT |Price without VAT | |Name |Price with VAT |Price without VAT |
-|Gen7 v1.PCB, including developer donation                 EUR 16.50|  EUR 13.90| +|Gen7 v2.PCB, including developer donation | EUR 16.50| EUR 13.90| 
-|Gen7 v1.Components Kit (with ATmega1284P and bootloader) |  EUR 25.50 EUR 21.40+|Gen7 v2.Components Kit (with LPC1114 CPU) | EUR  22.-| EUR 18.50
-|Gen7 v1.Connectors Kit                                   |  EUR 13.50|  EUR 11.30| +|Gen7 v2.Connectors Kit                    EUR  9.50| EUR   8.-| 
-|Gen7 Opto Endstop PCB (one piece)                          |   EUR  2.-|  EUR  1.70+|3-pack Mechanical Endstops with connectors  | EUR  4.50| EUR  3.80
-|Gen7 Opto Endstop Parts Kit (for one endstop)              |   EUR  2.- EUR  1.70| +|Shipping International                      EUR   5.-| EUR   5.-| 
-|ATmega1284P alone, with bootloader                           EUR  8.- EUR  6.70+|Shipping International PCB only             | EUR  2.50| EUR  2.50|
-|Shipping International                                     |   EUR  5.-|   EUR  5.-| +
-|Shipping International PCB only                             EUR  2.50|  EUR  2.50|+
  
 Prices including VAT apply to citizens of the European Union. Customers outside the European Community qualify for the VAT-free, lower prices. Prices including VAT apply to citizens of the European Union. Customers outside the European Community qualify for the VAT-free, lower prices.
Line 32: Line 30:
 An often requested combination includes the following: An often requested combination includes the following:
  
-  * 1x Gen7 v1.PCB +  * 1x Gen7 v2.PCB 
-  * 1x Gen7 v1.Components Kit +  * 1x Gen7 v2.Components Kit 
-  * 1x Gen7 v1.Connectors Kit +  * 1x Gen7 v2.Connectors Kit 
-  * 3x Gen7 Endstop PCB +  * 1x 3-pack Mechanical Endstops
-  * 3x Gen7 Endstop Parts+
   * Shipping   * Shipping
  
 +===== Gen7 Endstop =====
  
-======SevenSwitch======+**Gen7 Endstop** is an optical endstop using a light barrier. It was the recommended endstop for Gen7 v1.5 and before. Designed for 5\_V and 3.3\_V signals, so it can be connected to a Gen7-ARM 2.0 by one of the SPI connectors.
  
-SevenSwitch v1.2 with device plug and disk power connector+==== Orderable Items ====
  
-A SevenSwitch with KK156 device connector +|Name |Price with VAT |Price without VAT | 
-and disk power connector+|Gen7 Opto Endstop PCB (3-pack)           | EUR  6.-| EUR  5.10| 
-SevenSwitch v1.2 with 2x screw terminal+|Gen7 Opto Endstop Parts Kit (for 3-pack) | EUR  6.-| EUR  5.10| 
 +|Shipping International                   | EUR  5.-| EUR   5.-| 
 +|Shipping International PCBs only         | EUR 2.50| EUR  2.50|
  
-A SevenSwitch with screw terminals for 
-both, device and power supply connector. 
  
-For details, see SevenSwitch in the RepRap Wiki. The PCBs are manufactured on a RepRap machine. The Parts Kit matches the table on the Wiki page, including alternative parts for all configurations, pluggable connectors as well as screw terminals, 12 V and 24 V variants.+===== SevenSwitch =====
  
-Name  Price with VAT  Price without VAT +{{:gen7:sevenswitch_1.2_assembled_kk156_dp.jpeg?300 |A SevenSwitch with KK156 device connector and disk power connector.}} 
-SevenSwitch 1.2 PCB, including developer donation  EUR  3.-  EUR  2.50 + 
-SevenSwitch 1.2 Parts Kit (Components & Connectors)  EUR  5.40  EUR  4.50 +The **SevenSwitch** is a general purpose DC switch, useful for operating heated beds, heaters, fans and similar devices by 5\_V operated electronics, like Generation 6 Electronics, RAMPS, Sanguinololu, Generation 7 Electronics and similars. The only input needed is a 5\_V signal. It's fast enough to run at 80\_kHz PWM, strong enough to switch up to 15\_Ampéres and allows voltages of up to 30\_V, including 12 and 24\_Volts. 
-SevenSwitch 1.2 readily soldered  EUR 13.30  EUR 11.20 + 
-Shipping International  EUR  5.-  EUR  5.- +{{ :gen7:sevenswitch_1.2_assembled_st_st.jpeg?300|A SevenSwitch with screw terminals for both, device and power supply connector.}} 
-Shipping International PCB only: EUR  2.50  EUR  2.50+ 
 +For details, see [[http://reprap.org/wiki/SevenSwitch|SevenSwitch in the RepRap Wiki]]. The PCBs are manufactured on a RepRap machine. The Parts Kit matches the table on the Wiki page, including alternative parts for all configurations, pluggable connectors as well as screw terminals, 12\_V and 24\_V variants. 
 + 
 +==== Orderable Items ==== 
 + 
 +|Name |Price with VAT |Price without VAT| 
 +|SevenSwitch 1.2 PCB, including developer donation   |   EUR  3.-|  EUR  2.50| 
 +|SevenSwitch 1.2 Parts Kit (Components & Connectors) |  EUR  5.40|  EUR  4.50| 
 +|SevenSwitch 1.2 readily soldered                    |  EUR 13.30|  EUR 11.20| 
 +|Shipping International                                EUR  5.-|   EUR  5.-| 
 +|Shipping International PCB only                     |  EUR  2.50|  EUR  2.50|
  
 Prices including VAT apply to citizens of the European Union. Customers outside the European Community qualify for the VAT-free, lower prices. Prices including VAT apply to citizens of the European Union. Customers outside the European Community qualify for the VAT-free, lower prices.
-How to purchase 
  
-======Ordering======+===== Ordering =====
  
 For now, please order by emailing to Traumflug (mah@jump-ing.de). For now, please order by emailing to Traumflug (mah@jump-ing.de).
  
-For European Citizens, payment via (SEPA) bank transfer is somewhat preferred (no fees here)+Payment via bank wire is somewhat preferred (no fees here). For European citizens that's a SEPA bank transfer, for other parts of the world [[https://transferwise.com/|TransferWise]] is a good, low-fees choice:
  
-  Account no.: 7334010 
   Account holder: Markus Hitter   Account holder: Markus Hitter
-  IBAN: DE38 2009 0500 0007 3340 10 +  IBAN: DE26 5001 0517 5421 1942 18 
-  BIC/SWIFT-Code: GENODEF1S15 (Netbank AG, Germany)+  BIC/SWIFT-Code: INGDDEFFXXX (ING-DiBa, Germany)
  
-alternatively, PayPal is also fine (fees about EUR 1.50 here)+Alternatively, PayPal is also fine (fees about EUR 1.50 here):
  
   Account mah@jump-ing.de   Account mah@jump-ing.de
  
-======Addresses, legal stuff======+===== Addresses, legal stuff =====
  
 RepRap DIY is an outlet of: RepRap DIY is an outlet of:
Line 90: Line 96:
   Verantwortlich gem. §6 MDStV: Markus Hitter   Verantwortlich gem. §6 MDStV: Markus Hitter
   Umsatzsteuer-ID: DE 171 017 618   Umsatzsteuer-ID: DE 171 017 618
 +  
 +==== General Data Protection Regulation (GDPR) ====
 +
 +We're neither interested in personal data, nor do we try to collect or use such data. In detail:
 +
 +  * Pages at reprap-diy.com do not use trackers.
 +  * Visiting pages at reprap-diy.com stores up to three cookies in your browser to follow the session. These cookies get deleted when the session ends (when you close your browser).
 +  * Creating an account at reprap-diy.com stores your email address, content of the //Real name// field and an encrypted hash of your password.
 +  * Logging into an account and checking the //Remember me// checkbox stores another, permanent cookie (valid for one year) to keep you logged in. To remove this cookie, log out.
 +  * Each page edit stores the username of the user who did the edit. This information cannot get removed, but if the related account was removed, it also cannot be mapped to an email address or other personal data.
 +  * During page editing your IP address is used to lock the page against a competing edit. The address gets removed when the edit gets saved or canceled.
 +  * Some of the pages on reprap-diy.com may contain external videos. For YouTube we use the "privacy enhanced" youtube-nocookie.com domain that will not track your visit. Your IP address will be visible to the server providing the video, though. 
 +  * To view the data stored about you at reprap-diy.com, look at your  [[start?do=profile|user profile]].
 +  * To remove this data, go to your [[start?do=profile|user profile]] and delete your account.
  
-====Urheberrecht====+==== Urheberrecht ====
  
 © Alle Rechte vorbehalten. © Alle Rechte vorbehalten.
Line 102: Line 122:
 Die bereitgestellten Informationen auf der Website www.reprap-diy.com wurden sorgfältig geprüft und werden regelmäßig aktualisiert. Jedoch kann keine Haftung oder Garantie dafür übernommen werden, dass alle Angaben zu jeder Zeit vollständig, richtig und in letzter Aktualität dargestellt sind. Dies gilt insbesondere für alle Links zu anderen Websites, auf die direkt oder indirekt verwiesen wird. Hinsichtlich der Links erklärt Markus Hitter ausdrücklich, dass sie keinerlei Einfluss auf die Gestaltung und die Inhalte der verlinkten Seiten hat und sich diese Inhalte nicht zu eigen macht. Die bereitgestellten Informationen auf der Website www.reprap-diy.com wurden sorgfältig geprüft und werden regelmäßig aktualisiert. Jedoch kann keine Haftung oder Garantie dafür übernommen werden, dass alle Angaben zu jeder Zeit vollständig, richtig und in letzter Aktualität dargestellt sind. Dies gilt insbesondere für alle Links zu anderen Websites, auf die direkt oder indirekt verwiesen wird. Hinsichtlich der Links erklärt Markus Hitter ausdrücklich, dass sie keinerlei Einfluss auf die Gestaltung und die Inhalte der verlinkten Seiten hat und sich diese Inhalte nicht zu eigen macht.
  
-  
start.1445959361.txt.gz · Last modified: 2018/05/27 16:10 (external edit)