Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
connect_sevenswitch_to_ramps [2016/05/20 16:03] – [Finding a Signal Pin] Traumflug | connect_sevenswitch_to_ramps [2023/10/13 22:35] – [Finding a Signal Pin] Remove direct HTML. Traumflug | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Connect a SevenSwitch to a RAMPS ====== | ||
- | One of the oddities of the RepRap community is the heated bed connector on the very popular RAMPS controller. It's undersized for modern beds and this is known for years, but nobody fixes it (which would trivial). | ||
- | |||
- | Anyways. One of the solutions to work around this situation is to use a [[SevenSwitch]] to do the hard work. Here we show how to connect this switch to a RAMPS and how to tweak the popular firmwares to work with the new switch instead of the old one. | ||
- | |||
- | ===== Finding a Signal Pin ===== | ||
- | |||
- | {{ : | ||
- | |||
- | First step is to find an appropriate signal pin on the RAMPS. " | ||
- | |||
- | Some vendors solder in pins there already, others don't. If there are none, you have to do this yourself. Standard 0.1" spaced pins are fine. Another option is to solder the signal wire directly into the board. | ||
- | |||
- | < | ||
- | {{ : | ||
- | |||
- | There are 4 signal pins available for interfacing in the servo section: D4, D5, D6 and D11. Each of them works equally well. Connecting more than one SevenSwitch is possible, too. | ||
- | |||
- | ===== Wiring ===== | ||
- | |||
- | {{ : | ||
- | |||
- | The above picture shows how things get together: | ||
- | |||
- | * Thin lines are signal wires which draw negligible current, so one can use thin wires. Typically used wire is 0.14\_mm² or AWG\_35. | ||
- | * Thick lines mean wires carrying substantial current, so it needs thick wires. Required thickness depends on the current going to the heated bed; using a 1.5\_mm² (AWG\_15) wire is almost always sufficient. For a little extra bed power, many use 2.5\_mm (AWG\_11) size. | ||
- | * The green line is the signal wire. This one turns the switch on and off. | ||
- | * Power supply doesn' | ||
- | * Polarisation of these two wires going to the heated bed doesn' | ||
- | * Do not connect the heated bed, yet. Without the bed connected there are no currents flowing, so nothing can overheat. The green LED will show wether the switch is working. | ||
- | ===== Why not ... ===== | ||
- | |||
- | Some people tend to try connecting a SevenSwitch a different way. Let's elaborate on this. | ||
- | |||
- | ==== ... using D8, the original heated bed connector? ==== | ||
- | |||
- | Using D8 is a possible, but poor choice for several reasons: | ||
- | |||
- | * D8 is switched by a high current MOSFET, which is like using a truck for transporting a single cookie. There' | ||
- | * Due to being behind a MOSFET, signal on D8 is inverted. Without firmware modification, | ||
- | * There are better uses for this output, e.g. for driving a fan, lighting, heaters, whatever draws less than 10\_amps and has no coil inside. | ||
- | * If the RAMPS is operated with 24\_volts, it'll destroy the SevenSwitch' |
connect_sevenswitch_to_ramps.txt · Last modified: 2023/10/30 23:53 (external edit)